{"product_id":"bigtreetech-manta-m5p-cb1-v2-2-core-board-for-klipper-compact-linux","title":"BIGTREETECH Manta M5P+CB1 V2.2 Core Board for Klipper - Compact Linux","description":"\u003cp\u003eIn this review the BIGTREETECH Manta M5P+CB1 V2.2 is judged as a purpose-built controller for makers who want a compact, integrated Klipper-capable platform. The setup pairs a 32-bit Manta M5P mainboard with the CB1 V2.2 core module so the unit can run a full Linux environment and host Klipper directly, removing the need for a separate Raspberry Pi in many builds. If you want a tidy Ender 3 or Voron V0 install with HDMI or SPI display support and onboard networking, this combination is the clearest reason to consider it.\u003c\/p\u003e\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBorn for Klipper:\u003c\/strong\u003e The Manta M5P is designed to run Klipper with the CB1 core, simplifying wiring and integration compared with a separate single-board computer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuad-core CB1 core:\u003c\/strong\u003e The CB1 V2.2 uses an ARM Cortex-A53 quad-core processor and 1GB DDR3 RAM so it can run Linux and Debian-based tools for local processing and remote control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOnboard HDMI and SPI display:\u003c\/strong\u003e HDMI output and SPI touch support allow using BIGTREETECH HDMI5\/HDMI7 or SPI touch screens with minimal cabling for a direct, responsive UI.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNetwork and camera ready:\u003c\/strong\u003e Built-in 100M Ethernet and WiFi plus a plug-and-play USB camera option make monitoring prints and remote access straightforward.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlexible motor driver support:\u003c\/strong\u003e Integrated SPI and UART modes for TMC drivers and DIAG pin access make it simple to use TMC2209, TMC2208 or other compatible drivers with jumper configuration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFirmware and servicing:\u003c\/strong\u003e MCU firmware is upgradeable via SD or DFU using Klipper make flash, and documentation and update steps are provided on BIGTREETECH GitHub.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWho It's For\u003c\/h2\u003e\n\u003cp\u003eThis board combo is ideal for experienced 3D printer hobbyists and small workshop users who want to run \u003cstrong\u003eKlipper\u003c\/strong\u003e without a separate Raspberry Pi and prefer a compact, integrated solution for Ender 3 or Voron V0 frames. It appeals to builders who value tidy wiring, onboard display output, and the option to run Debian or other Linux tools directly on the printer controller.\u003c\/p\u003e\n\u003cp\u003eIt is less suitable for users who need an out-of-the-box consumer experience with step-by-step manufacturer firmware menus, or for absolute beginners who are uncomfortable flashing firmware and following GitHub setup instructions. Newcomers may prefer a simpler Marlin-only solution or a guided kit.\u003c\/p\u003e\n\u003ch2\u003ePros \u0026amp; Cons\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003ePros\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCombines a 32-bit Manta M5P controller with a CB1 Linux core so Klipper runs natively and wiring is reduced.\u003c\/li\u003e\n\u003cli\u003eHDMI and SPI display support plus USB camera and networking enable a modern, integrated UI and remote monitoring.\u003c\/li\u003e\n\u003cli\u003eFlexible driver interfaces and replaceable fuse make upgrades and maintenance straightforward.\u003c\/li\u003e\n\u003cli\u003eDocumentation and firmware update procedures are provided on BIGTREETECH GitHub for advanced users.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSetup assumes familiarity with firmware flashing and Klipper; novices will face a learning curve.\u003c\/li\u003e\n\u003cli\u003eCB1 provides 1GB DDR3 which is fine for printer control but is not comparable to higher-end SBCs for heavy multitasking.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003eMainboard\u003c\/td\u003e\n\u003ctd\u003eManta M5P 32-bit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore board\u003c\/td\u003e\n\u003ctd\u003eCB1 V2.2 quad-core ARM Cortex-A53\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMemory\u003c\/td\u003e\n\u003ctd\u003e1GB DDR3 RAM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNetwork\u003c\/td\u003e\n\u003ctd\u003e100M Ethernet and 100M WiFi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDisplay interfaces\u003c\/td\u003e\n\u003ctd\u003eHDMI and SPI touch screen\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMotor driver support\u003c\/td\u003e\n\u003ctd\u003eSPI and UART modes (TMC2209, TMC2208, TMC5160T Pro etc.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFirmware options\u003c\/td\u003e\n\u003ctd\u003eRun Klipper on Linux or Marlin without CB1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch2\u003eOur Verdict\u003c\/h2\u003e\n\u003cp\u003eThe Manta M5P+CB1 V2.2 is a sensible choice for tinkerers and small workshop builders who want an integrated Klipper-capable controller with HDMI\/SPI display and networked monitoring. It removes the need for a separate Raspberry Pi in many builds and offers flexible driver support and documented firmware update paths, making it good value for users comfortable with flashing and Linux-based setup.\u003c\/p\u003e\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eCan this run Klipper out of the box?\u003c\/strong\u003e\u003cbr\u003eWith the CB1 attached it is designed to run Klipper under Linux; follow the BIGTREETECH GitHub instructions for setup and firmware flashing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it replace a Raspberry Pi?\u003c\/strong\u003e\u003cbr\u003eYes, the CB1 provides a Linux environment so many installs do not require a separate Raspberry Pi CM4 or Pi board.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it support common TMC drivers?\u003c\/strong\u003e\u003cbr\u003eYes, the board supports SPI and UART modes for popular TMC drivers like TMC2209 and TMC2208 and includes DIAG pin access and jumper configuration.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":48233679257819,"sku":"B0C2YVYYMR","price":82.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0724\/1043\/1707\/files\/71Geqc9OqVL._AC_SL1500.jpg?v=1770911087","url":"https:\/\/gearmusthave.com\/products\/bigtreetech-manta-m5p-cb1-v2-2-core-board-for-klipper-compact-linux","provider":"GearMustHave","version":"1.0","type":"link"}